CJ/T 190-2004 Replaced Industry standards-Urban construction

CJ/T 190-2004 Polyethlene/aluminum/polyethylene composite pipe press fitting

CJ/T 190-2004 Polyethlene/aluminum/polyethylene composite pipe press fitting

Publish Date: 2004-03-25 Implement Date: 2004-08-01 For services related to genuine standard inquiry, procurement, translation, and other related services in China, please Contact Us

Basic Information

Standard Code: CJ/T 190-2004

Standard Type: Industry standards

Standard Status: Replaced

is_force_gb: no

CCS Name: -

ICS Name: -

Publish Date: 2004-03-25

Implement Date: 2004-08-01

Pages: 24 pages

Scope

This standard specifies the definition, classification, requirements, test methods, inspection rules, marking, packaging, transportation, and storage of crimped fittings for aluminum-plastic composite pipes (referred to as fittings).
This standard applies to aluminum-plastic pipes (referred to as pipes) used with crimped fittings for conveying fluids (cold water, drinking water distribution systems for cold and hot water, water supply and distribution systems, heating systems, underground irrigation systems, industrial special fluids, compressed air, gas, etc.) under the maximum allowable working pressure specified in GB/T 18997.1—2003 "Aluminum-Plastic Composite Pressure Pipes—Part 1: Aluminum-Plastic Pipes with Overlapped Welded Aluminum Tubes".
Crimped fittings for aluminum-plastic composite pipes with overlapped welded aluminum tubes and crimped fittings for cross-linked polyethylene plastic pipes can refer to this standard.

Development Information

Word Count: 36 Thousand words Pages: 24 pages

Superseded by the following standards

CJ/T 190-2015 Polyethlene/aluminum/polyethylene composite pipe press fitting

Referenced Standards

GB/T 1176-1987 Specification for cast copper alloys GB/T 1220-1992 Stainless steel bars GB/T 2828.1-2003 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection GB/T 2829-2002 Sampling procedures and tables for periodic inspection by attributes (Apply to inspection of process stability) GB/T 2918-1998 Plastics—Standard atmospheres for conditioning and testing GB/T 5231-2001 Wrought copper and copper alloys chemical composition limits and forms of wrought products GB/T 5720-1993 Test methods for rubber O rings GB/T 7306.1-2000 Pipe threads with 55 degree thread angle where pressure-tight joints are made on the threads—Part 1:Parallel internal and taper external threads GB/T 14832-1993 Test of compatibility between rubber material and hydraulic fluid GB/T 18997.1-2003 Polyethylene/Aluminum/Polyethylene composite pressure pipe—Part 1:PE/AL/PE pipe overlap-welded by aluminum pipe GB/T 18997.2-2003 Polyethylene/Aluminum/Polyethylene composite pressure pipe—Part 2:PE/AL/PE pipe butt-welded by aluminum pipe

Related Standards

DZ/T 0101.12-1994 Active

DZ/T 0101.12-1994 Geological instrument manufacturing time quota for printed circuit board

Publish Date: 1994-01-27

JJG 204-1980 Active

JJG 204-1980 Meteorological Ventilation Psychrometer

Publish Date: 1980-07-11

SC 53-1980 Active

SC 53-1980 Transfer blade hydraulic steering gear repair quality standard

Publish Date: 1981-07-01

DZ 4-1981 Replaced

DZ 4-1981

Publish Date: 1981-08-20

SC 69-1982 Active

SC 69-1982 ZSS-12 Flash-type seawater desalination production device technical specifications

Publish Date: 1982-01-20

SC 72-1982 Active

SC 72-1982 Steel Fishing Boat Builder Quality Standards and Mooring Equipment Installation Technical Requirements

Publish Date: 1982-03-30