GB/T 7636-1987
Abolished
CJ/T 190-2015
Active
Industry standards-Urban construction
CJ/T 190-2015 Polyethlene/aluminum/polyethylene composite pipe press fitting
CJ/T 190-2015 Polyethlene/aluminum/polyethylene composite pipe press fitting
Basic Information
Standard Code:
CJ/T 190-2015
Standard Type:
Industry standards
Standard Status:
Active
is_force_gb:
no
CCS Name:
Water supply and drainage projects
ICS Name:
\nGas supply system
Publish Date:
2015-07-03
Implement Date:
2016-01-01
Pages:
17 pages
Scope
This standard specifies the terms and definitions, classification and marking, materials, requirements, test methods, inspection rules, marking, packaging, transportation, and storage of crimped fittings for aluminum-plastic composite pipes (referred to as fittings).
This standard applies to crimped fittings for aluminum-plastic composite pipes (referred to as pipes) used to transport fluids with a maximum allowable working pressure of not more than 1.0 MPa (such as cold water, hot water, natural gas, heating, compressed air, and special fluids).
Development Information
Replace the following standards
Referenced Standards
GB/T 1176-1987 Specification for cast copper alloys
GB/T 1176-2013 Casting copper and copper alloys
GB/T 1220-1992 Stainless steel bars
GB/T 1220-2007 Stainless steel bars
GB/T 2828.1-2003 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection
GB/T 2828.1-2012 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection
GB/T 3280-1992 Cold rolled stainless steel sheets and plates
GB/T 3280-2007 Cold rolled stainless steel plate, sheet and strip
GB/T 3280-2015 Cold rolled stainless steel plate, sheet and strip
GB/T 5231-2001 Wrought copper and copper alloys chemical composition limits and forms of wrought products
GB/T 5231-2012 Designation and chemical composition of wrought copper and copper alloys
GB/T 5231-2022 Designation and chemical composition of wrought copper and copper alloys
GB/T 5720-1993 Test methods for rubber O rings
GB/T 5720-2008 Test methods for rubber O-rings
GB/T 6111-2003 Thermoplastics pipes for the conveyance of fluids-Resistance to internal pressure—Test method
GB/T 6111-2018 Thermoplastics piping systems for the conveyance of fluids—Determination of the resistance to internal pressure
GB/T 7306.1-2000 Pipe threads with 55 degree thread angle where pressure-tight joints are made on the threads—Part 1:Parallel internal and taper external threads
GB/T 7307-2001 Pipe threads with 55 degree thread angle where pressure-tight joints are not made on the threads
GB/T 14832-1993 Test of compatibility between rubber material and hydraulic fluid
GB/T 14832-2008 Test methods for compatibility between hydraulic fluids and standard elastomeric materials
GB/T 15560-1995 Standard test method for short-time hydraulic failure and resistance to constant internal pressure of the plastics pipes for the transport of fluids
GB/T 18997.1-2003 Polyethylene/Aluminum/Polyethylene composite pressure pipe—Part 1:PE/AL/PE pipe overlap-welded by aluminum pipe
GB/T 18997.1-2020 Plastic/aluminum/plastic composite pressure pipes—Part 1:Composite pipes overlap-welded by aluminum pipe
GB/T 18997.2-2003 Polyethylene/Aluminum/Polyethylene composite pressure pipe—Part 2:PE/AL/PE pipe butt-welded by aluminum pipe
GB/T 18997.2-2020 Plastic/aluminum/plastic composite pressure pipes—Part 2:Composite pipes butt-welded by aluminum pipe
GB/T 19278-2003 General terms and their definitions of thermoplastic pipes, fittings and valves
GB/T 19278-2018 General terms and their definitions of thermoplastic pipes,fittings and valves
Related Standards
GB/T 7637-1987
Abolished
GB/T 7637-1987 Operation rules of construction and installation of biogas pipelines for peasant household
GB 15558.1-1995
Replaced
GB 15558.1-1995 Buried polyethylene (PE) pipes for the supply of gaseous fuels
GB 15558.2-1995
Replaced
GB 15558.2-1995 Buried polyethylene (PE) fittings for the supply of gaseous fuels
GB 16802-1997
Replaced
GB 16802-1997 Town gas pressure regulators
GB 17264-1998
Replaced