GB/T 7346-1998
Replaced
GB/Z 20833.5-2023
Active
National standards
GB/Z 20833.5-2023 Rotating electrical machines—The winding insulation—Part 5:Off-line measurement of partial discharge inception voltage under repetitive impulse voltage
GB/Z 20833.5-2023 Rotating electrical machines—The winding insulation—Part 5:Off-line measurement of partial discharge inception voltage under repetitive impulse voltage
Basic Information
Standard Code:
GB/Z 20833.5-2023
Standard Type:
National standards
Standard Status:
Active
is_force_gb:
no
CCS Name:
Rotating motor
ICS Name:
Rotating motor comprehensive
Publish Date:
2023-09-07
Implement Date:
2024-04-01
Publisher:
国家市场监督管理总局、国家标准化管理委员会
Technical Committee:
全国旋转电机标准化技术委员会(SAC/TC 26)
Pages:
37 pages
Scope
本文件规定了绕组绝缘在重复冲击电压下局部放电起始和熄灭电压的离线测量方法。
本文件适用于电压型变频器供电的旋转电机。
Development Information
Drafting Units:
上海电机系统节能工程技术研究中心有限公司、中车永济电机有限公司、SEW-电机(苏州)有限公司、苏州巨峰电气绝缘系统股份有限公司、山东华力电机集团股份有限公司、卧龙电气驱动集团股份有限公司、江苏大通机电有限公司、江苏上骐集团有限公司、瑞昌市森奥达科技有限公司、中国大唐集团科学技术研究总院有限公司华北电力试验研究院、上海电器科学研究所(集团)有限公司、安徽威能电机有限公司、大连钰霖电机有限公司、东方电气集团东方电机有限公司、南阳防爆(苏州)特种装备有限公司、西门子电机(中国)有限公司、上海迈昆控制系统有限公司、上海诺百川新能源科技有限公司
Drafting Persons:
刘芮、张生德、郑瑞娟、张运哲、周成、尹志华、胥鹏涛、肖先雄、印光宇、王贤长、张兴滨、佟安妮、蒋丹枫
Referenced Standards
GB/T 23642-2017 Electrical insulating materials and systems—Electrical measurement of partial discharges(PD) under short rise time and repetitive voltage impulses
IEC 60034-27-1
IEC TS 61934
IEC TS 62478
Adopt standards
IEC TS 60034-27-5:2021
Related Standards
GB/T 4772.1-1999
Replaced
GB/T 4772.1-1999 Dimensions and output series for rotating electrical machines—Part 1:Frame numbers 56 to 400 and flange numbers 55 to 1080
GB/T 4772.2-1999
Active
GB/T 4772.2-1999 Dimensions and output series for rotating electrical machines— Part 2:Frame numbers 355 to 1000 and flange numbers 1180 to 2360
GB/T 4772.3-1999
Active
GB/T 4772.3-1999 Dimensions and output series for rotating electrical machines— Part 3:Samll built-in motors flange numbers BF10 to BF50
GB 10068-2000
Replaced
GB 10068-2000 Mechanical vibration of certain machines with shaft heights 56mm and higher—Measurement,evaluation and limits of vibration
GB/T 17948.1-2000
Replaced