GB 3883.10-1991
Replaced
GB/T 3883.11-2012
Replaced
National standards
GB/T 3883.11-2012 Safety of hand-held motor-operated electric tools—Part 2:Particular requirements for reciprocating saws(jig and sabre saws)
GB/T 3883.11-2012 Safety of hand-held motor-operated electric tools—Part 2:Particular requirements for reciprocating saws(jig and sabre saws)
Basic Information
Standard Code:
GB/T 3883.11-2012
Standard Type:
National standards
Standard Status:
Replaced
is_force_gb:
no
CCS Name:
Electric tools
ICS Name:
Electric tools
Publish Date:
2012-11-05
Implement Date:
2013-05-01
Pages:
13 pages
Scope
Except for the provisions mentioned below, this chapter of GB 3883.1—2008 applies.
Addition:
This section applies to reciprocating saws, such as curved saws and knife saws.
Development Information
Same series standard
GB/T 3883.2-2012 Safety of hand-held motor-operated electric tools—Part 2:Particular requirements for screwdrivers and impact wrenches
GB/T 3883.4-2012 Safety of hand-held motor-operated electric tools—Part 2:Particular requirements for sanders and polishers other than disk type
GB/T 3883.6-2012 Safety of hand-held motor-operated electric tools—Part 2:Particular requirements for drills and impact drills
GB/T 3883.7-2012 Safety of hand-held motor-operated electric tools—Part 2:Particular requirements for hammers
GB/T 3883.8-2012 Safety of hand-held motor-operated electric tools—Part 2:Particular requirements for sheet metal shears and nibblers
GB/T 3883.9-2012 Safety of hand-held motor-operated electric tools—Part 2:Particular requirements for tappers
GB/T 3883.12-2012 Safety of hand-held motor-operated electric tools—Part 2:Particular requirements for concrete vibrators
GB/T 3883.19-2012 Safety of hand-held motor-operated electric tools—Part 2:Particular requirements for drain cleaners
GB/T 3883.20-2012 Safety of hand-held motor-operated electric tools—Part 2:Particular requirements for strapping tools
GB/T 3883.21-2012 Safety of hand-held motor-operated electric tools—Part 2:Particular requirements for band saws
Replace the following standards
Superseded by the following standards
Referenced Standards
GB/T 2423.55-2006 Environmental testing for electric and electronic products—Part 2:Test methods—Test Eh:Hammer tests
GB/T 4207-2003 Method for determining the comparative and the proof tracking indices of solid insulating materials under moist conditions
GB/T 4208-2008 Degrees of protection provided by enclosure(IP code)
GB 4706.1-2005 Household and similar electrical appliances—Safety—Part 1:General requirements
GB/T 4956-2003 Non-magnetic coatings on magnetic substrates—Measurement of coating thickness-Magnetic method
GB/T 5465.2-1996 Graphical symbols for use on electrical equipment
GB
8898-2001
GB/T 11918-2001 Plugs, socket-outlets and couplers for industrial purposes—Part 1:General requirements
GB/T 11919-2001 Plugs, socket-outlets and couplers for industrial purposes—Part 2:Dimensional interchangeability requirements for pin and contact-tube accessories
GB/T 14536.1-2008 Automatic electrical controls for household and similar use—Part 1:General requirements
GB 15092.1-2003 Switches for appliances Part 1:General requirements
GB
19212.1-2003
GB 19212.5-2006 Safety of power transformers, power supply units and similar—Part 5:Particular requirements for isolating transformers for general use
GB 19212.7-2006 Safety of power transformers, power supply units and similar—Part 7:Particular requirements for safety isolating transformers for general use
IEC 60061-1:2005
IEC 60320(所有部分)
IEC 60695-2-11
IEC 60695-11-5:2004
IEC
60695-11-10
IEC 60738-1
IEC 60760:1989
IEC 60884 (所有部分)
IEC 60825-1
IEC 60998-2-1
IEC 60999-1:1999
IEC 60906-1
IEC
61540:1997+1号修改件(1998)
ISO 3864-2
ISO 7010:2003
ISO 9772:2001
GB 5013.4-1997 Rubber insulated cables of rated voltages up to and including 450/750V—Part 4:Cords and flexible cables
GB/T 5013.4-2008 Rubber insulated cables of rated voltages up to and including 450/750 V—Part 4:Cords and flexible cables
GB 5023.5-1997 Polyvinyl chloride insulated cables of rated voltages up to and including 450/750V—Part 5:Flexible cables (cords)
GB/T 5023.5-2008 Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V—Part 5:Flexible cables (cords)
GB/T 6462-1986 Metallic and oxide coatings—Measurement of coating thickness—Microscopical method
GB/T 6462-2005 Metallic and oxide coatings—Measurement of coating thickness—Microscopical method
GB 9364.1-1997 Miniature fuses—Part 1:Definitions for miniature fuses and general requirement for miniature fuse-links
GB/T 9364.1-2015 Miniature fuses—Part 1:Definitions for miniature fuses and general requirement for miniature fuse-links
GB/T 11021-2007 Electrical insulation—Thermal classification
GB/T 11021-2014 Electrical insulation—Thermal evaluation and designation
GB 13140.3-1998 Connecting devices for low voltage circuits for household and similar purposes Part 2:Particular requirements for connecting devices as separate entities with screwless-type clamping units
GB/T 13140.3-2008 Connecting devices for low-voltage circuitsfor household and similar purposes—Part 2:Particular requirements for connecting devices as separate entities with screwless-type clamping units
GB/T 14472-1998 Fixed capacitors for use in electronic equipment—Part 14:Sectional specification:Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
GB/T 6462-2025 Metallic and oxide coatings—Measurement of coating thinckness—Microscopical method
Adopt standards
IEC 60745-2-11:2008(2.1版)
IEC 60745-1:2006(4.0版)
Related Standards
GB 3883.12-1991
Replaced
GB 3883.12-1991 Safety of hand-held motor-operated electric tools—Part 2:Particular requirements for concrete vibrators (internal vibrators)
GB 3883.3-1991
Replaced
GB 3883.3-1991 Safety of hand-held motor-operated electric tools Part 2:Particular requirements for electric grinders, polishers and disk-type sanders
GB 3883.6-1991
Replaced
GB 3883.6-1991 Safety of hand-held motor-operated electric tools—Part 2:Particular requirements for electric drills
GB 13960-1992
Replaced
GB 13960-1992 Safety of transportable motor-operated electric tools—Part 1:General requirements
GB/T 13956-1992
Abolished