GB 6450-1986
Replaced
JB/T 8448.2-2004
Abolished
Industry standards-Mechanical
JB/T 8448.2-2004 Technical specifications of sealing articles for transformer and similar products Part 2:Corkrubber sealing articles
JB/T 8448.2-2004 Technical specifications of sealing articles for transformer and similar products Part 2:Corkrubber sealing articles
Basic Information
Standard Code:
JB/T 8448.2-2004
Standard Type:
Industry standards
Standard Status:
Abolished
is_force_gb:
no
CCS Name:
Transformer
ICS Name:
Transformers, reactors, and inductors
Publish Date:
2004-03-12
Implement Date:
2004-08-01
Pages:
11 pages
Development Information
Same series standard
Replace the following standards
JB/T 8448.2-1996
Superseded by the following standards
Referenced Standards
GB/T 1682-1994 Rubber, vulcanized—Determination of low-temperature brittleness(single test piece method)
GB/T 1690-1992 Rubber, vulcanized-Determination of the effect of liquids
GB/T 2828.1-2003 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection
GB/T 2828.1-2012 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection
GB/T 2828.2-2008 Sampling procedures for inspection by attributes—Part 2:Sampling plans indexed by limiting quality(LQ)for isolated lot inspection
GB/T 2828.3-2008 Sampling procedures for inspection by attributes—Part 3:Skip-lot sampling procedures
GB/T 2828.4-2008 Sampling procedures for inspection by attributes—Part 4:Procedures for assessment of declared quality levels
GB/T 2828.5-2011 Sampling procedures for inspection by attributes—Part 5:System of sequential sampling plans indexed by acceptance quality limit(AQL)for lot-by-lot inspection
GB/T 2828.10-2010 Sampling procedures for inspection by attributes—Part 10:Introduction to the GB/T 2828 series of standards for sampling for inspection by attributes
GB/T 2828.11-2008 Sampling procedures for inspection by attributes—Part 11:Procedures for assessment of declared quality levels for small population
GB/T 3672.1-2002 Rubber—Tolerances of products—Part 1:Dimensional tolerances
GB/T 528-1998 Rubber,vulcanized or thermoplastic—Determination of tensile stress-strain properties
GB/T 531-1999 Rubber—Determination of indentation hardness by means of pocket hardness meters
GB/T 5719-1995 Rubber sealings articles—Terminology
GB/T 5721-1993 General rules of identification, packaging, transportation and storage for rubber sealing products
GB/T 6039-1997 Rubber physical tests and chemical tests—Terms
GB/T 7759-1996 Rubber, Vulcanized or thermoplastic—Determination of compression set at ambient elevated or low temperatures
GB/T 7762-2003 Rubber, vulcanized or thermoplastic—Resistance to ozone cracking—Static strain test
GB/T 9865.1-1996 Rubber, vulcanized or thermoplastic—Preparation of samples and test pieces—Part1:Physical tests
JB/T 8448.1-2004 Technical Specification for Sealing Products Used in Transformer-type Products Part 1: Rubber Sealing Products
Related Standards
GB/T 7449-1987
Replaced
GB/T 7449-1987 Guide to the lightning impulse and switching impulse testing of power transformers and reactors
GB 13028-1991
Abolished
GB 13028-1991 Isolating transformers and safety isolating transformers Requirements
GB/T 14006-1992
Active
GB/T 14006-1992 Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment—Part 1:Transformers and inductors using YEI-1 laminations
GB/T 14860-1993
Replaced
GB/T 14860-1993 Generic specification for transformers and inductors for use in telecommunication and electronic equipment
GB/T 15164-1994
Replaced