CJ/T 225-2006
Replaced
CJ/T 111-2018
Active
Industry standards-Urban construction
CJ/T 111-2018 Sleeve-clipping type brass pipe fitting
CJ/T 111-2018 Sleeve-clipping type brass pipe fitting
Basic Information
Standard Code:
CJ/T 111-2018
Standard Type:
Industry standards
Standard Status:
Active
is_force_gb:
no
CCS Name:
Water supply and drainage projects
ICS Name:
Drainage system
Publish Date:
2018-11-16
Implement Date:
2019-05-01
Pages:
28 pages
Scope
This standard specifies the product classification, structure, and marking, materials, requirements, test methods, inspection rules, marking, packaging, transportation, and storage of copper pipe fittings used in building piping projects (hereinafter referred to as pipe fittings).
This standard applies to copper pipe fittings for aluminum-plastic composite pipes and plastic piping systems with a nominal size of 12 mm to 32 mm.
Development Information
Replace the following standards
Referenced Standards
GB/T 196-2003 General purpose metric screw threads—Basic dimensions
GB/T 197-2018 General purpose metric screw threads—Tolerances
GB/T 1184-1996 Geometrical tolerancing—Geometrical tolerance for features without individual tolerance indications
GB/T 1804-2000 General tolerances for linear and angular dimensions without individual tolerance indications
GB/T 7307-2001 Pipe threads with 55 degree thread angle where pressure-tight joints are not made on the threads
GB/T 15560-1995 Standard test method for short-time hydraulic failure and resistance to constant internal pressure of the plastics pipes for the transport of fluids
GB/T 18991-2003 Thermoplastics pipes and fittings for hot and cold water systems
GB/T 18997.2-2003 Polyethylene/Aluminum/Polyethylene composite pressure pipe—Part 2:PE/AL/PE pipe butt-welded by aluminum pipe
GB/T 1176-1987 Specification for cast copper alloys
GB/T 1176-2013 Casting copper and copper alloys
GB/T 2828.1-2003 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection
GB/T 2828.1-2012 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection
GB/T 5231-2001 Wrought copper and copper alloys chemical composition limits and forms of wrought products
GB/T 5231-2012 Designation and chemical composition of wrought copper and copper alloys
GB/T 5231-2022 Designation and chemical composition of wrought copper and copper alloys
GB/T 6111-2003 Thermoplastics pipes for the conveyance of fluids-Resistance to internal pressure—Test method
GB/T 6111-2018 Thermoplastics piping systems for the conveyance of fluids—Determination of the resistance to internal pressure
GB/T 15820-1995 Test of resistance to pull out of joints between polyethylene (PE) pressure pipes and fittings
GB/T 17219-1998 Standard for safety evaluation of equipment and protective materials in drinking water system
HG/T 2811-1996
GB/T 17219-2025 Hygienic safety evaluation of distribution equipment,protective materials and treatment materials in drinking water system
Related Standards
CJ/T 231-2006
Active
CJ/T 231-2006 Unplasticized polyvinyl chloride(PVC-U)and glass microsphere composite pipes for drainage
CJ/T 233-2006
Replaced
CJ/T 233-2006 Plastics inspection chambers for sewerage in building area
CJ/T 250-2007
Replaced
CJ/T 250-2007 High density polyethylene pipes and fittings for drainage inside buildings
CJ/T 270-2007
Replaced
CJ/T 270-2007 Steel reinforced spirally wound Polyethylene(PE) drainage pipe
CJ/T 273-2008
Replaced