GB/T 13996-1992
Abolished
GB/T 15972.32-2021
Active
National standards
GB/T 15972.32-2021 Specifications for optical fibre test methods—Part 32:Measurement methods and test procedures for mechanical characteristics—Coating strippability
GB/T 15972.32-2021 Specifications for optical fibre test methods—Part 32:Measurement methods and test procedures for mechanical characteristics—Coating strippability
Basic Information
Standard Code:
GB/T 15972.32-2021
Standard Type:
National standards
Standard Status:
Active
is_force_gb:
no
CCS Name:
Optical communication equipment
ICS Name:
Fiber optics and optical cables
Publish Date:
2021-10-11
Implement Date:
2022-05-01
Publisher:
国家市场监督管理总局、国家标准化管理委员会
Technical Committee:
全国通信标准化技术委员会(SAC/TC 485)
Pages:
12 pages
Scope
GB/T 15972的本部分规定了沿光纤纵轴向定量地机械剥去保护涂覆层所需的力的试验方法，确立了测量的统一试验程序和技术要求。
本部分适用于标称包层直径为125 μm且标称外涂覆层（包含紧包缓冲层）直径为的200 μm～900 μm的A1类、A2类、A3类、B类、C类和D类光纤的涂覆层可剥性测量。其他标称包层直径的光纤可参考本部分进行测量。
Development Information
Drafting Units:
中国信息通信科技集团有限公司、中国移动通信集团设计院有限公司、中国信息通信研究院
Drafting Persons:
刘骋、周辉智、刘泰、祁庆庆、戴广翀、许江波、韩超、胡古月、王冬香
Same series standard
GB/T 15972.10-2021 Specifications for optical fibre test methods—Part 10:Measurement methods and test procedures—General and guidance
GB/T 15972.20-2021 Specifications for optical fibre test methods—Part 20:Measurement methods and test procedures for dimensions—Fibre geometry
GB/T 15972.30-2021 Specifications for optical fibre test methods—Part 30: Measurement methods and test procedures for mechanical characteristics—Fibre proof test
GB/T 15972.31-2021 Specifications for optical fibre test methods— Part 31:Measurement methods and test procedures for mechanical characteristics—Tensile strength
GB/T 15972.34-2021 Specifications for optical fibre test methods—Part 34:Measurement methods and test procedures for mechanical characteristics—Fibre curl
GB/T 15972.41-2021 Specifications for optical fibre test methods—Part 41: Measurement methods and test procedures for transmission characteristics—Bandwidth
GB/T 15972.42-2021 Specifications for optical fibre test methods—Part 42:Measurement methods and test procedures for transmission characteristics—Chromatic dispersion
GB/T 15972.43-2021 Specifications for optical fibre test methods—Part 43: Measurement methods and test procedures for transmission characteristics—Numerical aperture
GB/T 15972.45-2021 Specifications for optical fibre test methods—Part 45:Measurement methods and test procedures for transmission characteristics—Mode field diameter
GB/T 15972.47-2021 Specifications for optical fibre test method—Part 47:Measurement methods and test procedures for transmission characteristics—Macrobending loss
GB/T 15972.49-2021 Specifications for optical fibre test methods—Part 49:Measurement methods and test procedures for transmission characteristics—Differential mode delay
GB/T 15972.54-2021 Specifications for optical fibre test methods—Part 54:Measurement methods and test procedures for environmental characteristics—Gamma irradiation
Replace the following standards
Referenced Standards
Adopt standards
IEC 60793-1-32:2018
Related Standards
GB/T 16529-1996
Active
GB/T 16529-1996 Splices for optical fibres and cables—Part 1:Generic specification—Hardware and accessories
GB/T 16849-1997
Replaced
GB/T 16849-1997 Generic specification on optical fibre amplifiers
GB/T 16850.1-1997
Replaced
GB/T 16850.1-1997 Basic specification for optical fibre amplifier test methods—Part 1:Test methods for gain parameters
GB/T 16529.2-1997
Active
GB/T 16529.2-1997 Splices for optical fibres and cables—Part 2:Sectional specification Splice organizers and closures for optical fibres and cables
GB/T 16529.3-1997
Active