GB 11032-2000
Abolished
GB/T 11032-2010
Replaced
National standards
GB/T 11032-2010 Metal-oxide surge arresters without gaps for a.c. systems
GB/T 11032-2010 Metal-oxide surge arresters without gaps for a.c. systems
Basic Information
Standard Code:
GB/T 11032-2010
Standard Type:
National standards
Standard Status:
Replaced
is_force_gb:
no
CCS Name:
Surge protector
ICS Name:
Other standards related to insulation
Publish Date:
2010-09-02
Implement Date:
2011-08-01
Pages:
145 pages
Scope
This standard applies to gapless metal oxide surge arresters (hereinafter referred to as surge arresters) designed to limit overvoltages in AC power systems.
Development Information
Superseded by the following standards
Referenced Standards
GB/T 191-2000 Packaging—Pictorial marking for handling of goods
GB 311.1-1997 Insulation co-ordination for high voltage transmission and distribution equipment
GB/T 311.2-2002 Insulation co-ordination—Part 2:Application guide for insulation co-ordination for high voltage transmission and distribution equipment
GB/T 775.1-2000
GB/T 775.3-2006 Test method for insulators—Part 3:Mechanical test methods
GB/T 2423.17-1993 Basic environmental testing procedures for electric and electronic products Test Ka:Salt mist
GB/T 2423.22-2002 Environmental testing for electric and electronic products—Part 2:Test methods Test N:Change of temperature
GB/T 2900.12-2008 Electrotechnical terminology—Surge arresters, low-voltage surge protective devices and components
GB/T 2900.19-1994 Electrotechnical terminology High-voltage test technique and insulation co-ordination
GB/T 3906-2006 Alternating-current metal-enclosed switchgear and controlgear for rated voltages above 3.6 kV and up to and including 40.5 kV
GB/T 4585-2004 Artificial pollution tests on high-voltage insulators to be used on a.c systems
GB/T 6553-2003 Test methods for evaluating resistance to tracking and erosion of electrical insulating materials used under severe ambient conditions
GB/T 7354-2003 Partial discharge measurements
GB 7674-1997 Gas-insulated metal-enclosed switchgear for rated voltages of 72.5 kV and above
GB/T 8905-1996 The guide for processing and measuring SF6 gas in power apparatus
GB/T 11023-1989
GB/T 16927.1-1997 High-voltage test techniques Part 1:General test requirements
GB/T 16927.2-1997 High-voltage test techniques Part 2:Measuring systems
GB/T 17467-1998 High-voltage/low-voltage prefabricated substations
GB/T 19519-2004 Composite insulators for a.c. overhead lines with a nominal voltage greater than 1000V—Definitions, test methods and acceptance criteria
IEC 60068-2-42:2003
IEC 60815:1986
IEC 61166:1993
CISPR 16-1:1999
CISPR 18-2:1986
JB/T 7618-1994 Arc-arrester sealed test immersion method
JB/T 9673-1999 Insulating product packaging
Adopt standards
IEC 60099-4:2006
Related Standards
GB/T 20639-2006
Active
GB/T 20639-2006 Artificial pollution testing of non-linear resistor type surge arresters with gaps
GB/T 18802.321-2007
Active
GB/T 18802.321-2007 Components for low-voltage surge protective devices—Part 321:Specifications for avalanche breakdown diode(ABD)
GB/T 18802.331-2007
Replaced
GB/T 18802.331-2007 Components for low-voltage surge protective devices—Part 331:Specification for metal oxide varistors(MOV)
GB/T 18802.341-2007
Active
GB/T 18802.341-2007 Components for low-voltage surge protective devices—Part 341:Specification for thyristor surge suppressors(TSS)
GB/T 2900.12-2008
Active