GB/T 3480.1-2019 Active National standards

GB/T 3480.1-2019 Calculation of load capacity of spur and helical gears—Part 1:Basic principles,introduction and general influence factors

GB/T 3480.1-2019 Calculation of load capacity of spur and helical gears—Part 1:Basic principles,introduction and general influence factors

Publish Date: 2019-12-31 Implement Date: 2020-07-01 For services related to genuine standard inquiry, procurement, translation, and other related services in China, please Contact Us

Basic Information

Standard Code: GB/T 3480.1-2019

Standard Type: National standards

Standard Status: Active

is_force_gb: no

CCS Name: Gears and gear transmissions

ICS Name: Gears and gear transmissions

Publish Date: 2019-12-31

Implement Date: 2020-07-01

Publisher: 国家市场监督管理总局、国家标准化管理委员会

Technical Committee: 全国齿轮标准化技术委员会(SAC/TC 52)

Pages: 92 pages

Scope

GB/T 3480的本部分介绍了直齿轮与斜齿轮承载能力计算的基本原理、概述及通用影响系数。它与ISO 6336-2、ISO 6336-3、ISO 6336-5及ISO 6336-6一起提供了一种可以对不同的齿轮设计进行比较的方法。它既不用于保证已组装的齿轮装置性能，也不供一般工程人员使用，而是供有经验的齿轮设计人员使用，他们能根据类似设计的知识对公式中的系数合理取值，并清楚各取值对计算结果有什么影响。
GB/T 3480中的公式是为了给渐开线圆柱直齿轮或斜齿轮的齿面接触强度和齿根弯曲强度计算提供一个广泛接受的方法而提出的。
GB/T 3480包含了如Hirt[1]、Strasser[2]和Brossmann[3]等人基于试验及理论研究的成果。用本法计算的结果与以往可接受的计算方法的结果相当一致（对于法向工作压力角不超过25°和分度圆螺旋角不超过25°的情况见参考文献[4]～[8]）。

Development Information

Drafting Units:

郑州机械研究所有限公司、郑州中机轨道交通装备科技有限公司、湖南大学、中机生产力促进中心、郑州高端装备与信息产业技术研究院有限公司、西安法士特汽车传动有限公司、山东华成中德传动设备有限公司、江苏中工高端装备研究院有限公司、重庆大学

Drafting Persons:

李峰、王志刚、吴鲁纪、李云鹏、周长江、韩伟、李五田、严鉴铂、鞠国强、李优华、刘忠明、王长路、张敬彩、张坤、管洪杰、范瑞丽、陈兵奎、张发勇、王国光、郑明、余飞鹏

Word Count: 174 Thousand words Pages: 92 pages

Replace the following standards

GB/T 3480-1997 Calculation methods of load capacity for involute cylindrical gears

Referenced Standards

GB/T 1356-2001 Cylindrical gears for general and heavy engineering—Standard basic rack tooth profile GB/T 3374.1-2010 Vocabulary of gear terms—Part 1:Definitions related to geometry GB/T 3505-2009 Geometrical Product Specifications (GPS)—Surface texture:Profile method—Terms,definitions and surface texture parameters GB/T 10095.1-2008 Cylindrical gears—System of accuracy—Part 1:Definitions and allowable values of deviations relevant to corresponding flanks of gear teeth GB/T 10610-2009 Geometrical Product Specifications(GPS)—Surface texture:Profile method—Rules and procedures for the assessment of surface texture ISO 6336-2 ISO 6336-3 ISO 6336-5 ISO 6336-6

Adopt standards

ISO 6336-1:2006

Related Standards

GB/T 4133-1984 Replaced

GB/T 4133-1984 The type and dimensions for positive drive of Morse tapers

Publish Date: 1984-01-18

GB/T 6404-1986 Replaced

GB/T 6404-1986 Determination of sound power level for noise emitted by gear units

Publish Date: 1986-05-19

GB 6413-1986 Abolished

GB 6413-1986 Calculation of scuffing load capacity for involute cylindrical gears

Publish Date: 1986-05-24

GB/T 6443-1986 Replaced

GB/T 6443-1986 Involute cylindrical gears-Information of the dimensional data to be given on the drawing

Publish Date: 1986-06-07

GB/T 1357-1987 Replaced

GB/T 1357-1987 Modules of involute cylindrical gears

Publish Date: 1987-06-11

GB/T 8543-1987 Replaced

GB/T 8543-1987 Determination of mechanical vibrations of gear units during acceptance testing

Publish Date: 1987-12-05