GB/T 18241.2-2000
Active
GB/T 18241.3-2018
Active
National standards
GB/T 18241.3-2018 Rubber lining—Part 3:Rubber lining for floatation machine
GB/T 18241.3-2018 Rubber lining—Part 3:Rubber lining for floatation machine
Basic Information
Standard Code:
GB/T 18241.3-2018
Standard Type:
National standards
Standard Status:
Active
is_force_gb:
no
CCS Name:
Other rubber products
ICS Name:
Other rubber and plastic products
Publish Date:
2018-05-14
Implement Date:
2018-12-01
Pages:
11 pages
Scope
This part of GB/T 18241 specifies the classification and marking of flotation machine linings (hereinafter referred to as linings), technical requirements, test methods, inspection rules, as well as the construction of linings, equipment completion inspection, quality assessment and marking, packaging, transportation, storage, and protection. This part applies to rubber linings for flotation machines and associated equipment in industries such as mining, metallurgy, rare earths, chemical industry, and coal. Note: Flotation machines and associated equipment include: flotation machine tanks, impeller supports, impellers, partitions, cover plates, drive units, feed boxes, intermediate boxes, tailings boxes, dosing boxes, washing devices, and conveying devices, etc.
Development Information
Replace the following standards
Referenced Standards
GB/T 8923.1-2011 Preparation of steel substrates before application of paints and related products—Visual assessment of surface cleanliness—Part 1:Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
GB/T 18241.1-2014 Rubber lining—Part 1:Anticorrosion lining for equipment
GB/T 528-1998 Rubber,vulcanized or thermoplastic—Determination of tensile stress-strain properties
GB/T 528-2009 Rubber,vulcanized or thermoplastic—Determination of tensile stress-strain properties
GB/T 529-1999 Rubber,vulcanized or thermoplastic—Determination of tear strength (Trouser,angle and crescent test pieces)
GB/T 529-2008 Rubber,vulcanized or thermoplastic—Determination of tear strength(Trouser,angle and crescent test pieces)
GB/T 531.1-2008 Rubber,vulcanized or thermoplastic—Determination of indentation hardness—Part 1:Duromerer method(Shore hardness)
GB/T 1689-1998 Rubber vulcanized—Determination of abrasion resistance(Akron machine)
GB/T 1689-2014 Rubber vulcanized—Determination of abrasion resistance (Akron machine)
GB/T 1690-1992 Rubber, vulcanized-Determination of the effect of liquids
GB/T 1690-2006 Rubber,vulcanized or thermoplastic—Determination of the effect of liquids
GB/T 1690-2010 Rubber,vulcanized or thermoplastic—Determination of the effect of liquids
GB/T 3512-2001 Rubber, vulcanized or thermoplastic—Accelerated ageing and heat resistance tests—Air-oven method
GB/T 3512-2014 Rubber, vulcanized or thermoplastic—Accelerated ageing and heat resistance tests—Air-oven method
GB/T 7760-2003 Rubber, vulcanized or thermoplastic—Determination of adhesion to a rigid substrate-90 degrees peel method
GB/T 11211-1989 Rubber, vulcanized—Determination of adhesion to metal—Tension method
GB/T 11211-2009 Rubber,vulcanized or thermoplastic—Determination of adhesion to metal—Two-plate method
HG/T 3849-2008 The determination of tensile strength and tensile elongation of hard rubber
HG/T 20677-2013 Design code for chemical equipment with rubber lining
Related Standards
GB/T 18241.3-2000
Replaced
GB/T 18241.3-2000 Rubber Iining—Part 3-Lining for floatation machine
GB 18241.1-2001
Replaced
GB 18241.1-2001 Rubber lining—Part 1 Anticorrosion lining for equipment
GB/T 20029-2005
Active
GB/T 20029-2005 Rubber isolation bearings for instruments and equipments
GB/T 18241.4-2006
Active
GB/T 18241.4-2006 Rubber lining—Part 4:Anticorrosion lining for flue gas desulfurization
GB 18173.1-2006
Replaced