GB 7251.2-1997
Replaced
GB/T 33346-2025
Active
National standards
GB/T 33346-2025 Busbar trunking systems(compact insulated busways) for wind power
GB/T 33346-2025 Busbar trunking systems(compact insulated busways) for wind power
Basic Information
Standard Code:
GB/T 33346-2025
Standard Type:
National standards
Standard Status:
Active
is_force_gb:
no
CCS Name:
Low-voltage distribution electrical equipment
ICS Name:
Low-voltage switchgear and controllers
Publish Date:
2025-08-01
Implement Date:
2026-02-01
Pages:
20 pages
Scope
This document specifies the usage conditions, interface characteristics, structural requirements, performance requirements, test verification, routine inspection, nameplates and markings, packaging, transportation, and storage methods for high-density wind power generation conductive rails (hereinafter referred to as "wind power bus ducts").
This document is applicable to wind power bus ducts with a rated voltage of no more than 1,000 V AC and a frequency of 50 Hz or 60 Hz, installed inside wind turbine towers or in the nacelles of wind turbines.
Development Information
Replace the following standards
Referenced Standards
GB/T 2423.4-1993 Basic environmental testing procedures for electric and electronic products—Test Db:Damp heat, cyclic
GB/T 2423.4-2008 Environmental testing for electric and electronic products—Part 2:Test method—Test Db:Damp heat,cyclic(12 h+12 h cycle)
GB/T 2423.10-1995 Environmental testing for electric and electronic products—Part 2:Test methods—Test Fc and guidance:Vibration (Sinusoidal)
GB/T 2423.10-2008 Environmental testing for electric and electronic products—Part 2:Tests methods Test Fc:Vibration(sinusoidal)
GB/T 2423.10-2019 Environmental testing—Part 2:Tests methods—Test Fc:Vibration(sinusoidal)
GB/T 2423.16-1999 Environmental testing for electric and electronic products—Part 2:Tests methods—Test J and guidance:Mould growth
GB/T 2423.16-2008 Environmental testing for electric and electronic products—Part 2:Test methods—Test J and guidance:Mold growth
GB/T 2423.16-2022 Environmental testing—Part 2:Test methods—Test J and guidance:Mould growth
GB/T 2423.17-1993 Basic environmental testing procedures for electric and electronic products Test Ka:Salt mist
GB/T 2423.17-2008 Environmental testing for electric and electronic products—Part 2:Test methods—Test Ka:Salt mist
GB/T 2423.17-2024 Environmental testing—Part 2:Test methods—Test Ka:Salt mist
GB 4208-1993 Degrees of protection provided by enclosure (IP code)
GB/T 4208-2008 Degrees of protection provided by enclosure(IP code)
GB/T 4208-2017 Degrees of protection provided by enclosure(IP code)
GB/T 7251.1-2023 Low-voltage switchgear and controlgear assemblies—Part 1:General rules
GB/T 7251.6-2015 Low-voltage switchgear and controlgear assemblies—Part 6:Busbar trunking systems(busways)
GB/T 13384-2008 General specifications for packing of mechanical and electrical product
Related Standards
GB/T 11022-1999
Replaced
GB/T 11022-1999 Common specifications for high-voltage switchgear and control gear standards
GB/T 18858.1-2002
Replaced
GB/T 18858.1-2002 Low-voltage switchgear and control gear Controller-device interface(CDIs)—Part 1:General rules
GB/T 18858.3-2002
Replaced
GB/T 18858.3-2002 Low-voltage switchgear and control gear—Controller-Device interface(CDI)—Part 3:Device Net
GB/Z 18859-2002
Replaced
GB/Z 18859-2002 Enclosed low-voltage switchgear and controlgear Assemblies—Guide for testing under conditions of arcing due to internal fault
GB 14048.4-2003
Replaced