GB/T 15139-1994 General technical standard for electrical equipment structure

GB/T 1182-1996 Geometrical tolerancing—Generalities, definitions, symbols, indications on drawings GB/T 1182-2008 Geometrical Product Specifications(GPS)—Geometrical tolerancing—Tolerances of form, orientation, location and run-out GB/T 1182-2018 Geometrical product specifications(GPS)—Geometrical tolerancing—Tolerances of form,orientation,location and run-out GB 1182~1184 GB/T 1184-1996 Geometrical tolerancing—Geometrical tolerance for features without individual tolerance indications GB/T 1800.1-1997 Limits and fits—Bases—Part 1:Terminology GB/T 1800.1-2009 Geometrical Product Specifications (GPS)—Limits and fits—Part 1:Bases of tolerances,deviations and fits GB/T 1800.1-2020 Geometrical product specifications (GPS)—ISO code system for tolerances on linear sizes—Part 1:Basis of tolerances, deviations and fits GB/T 1800.2-1998 Limits and fits—Bases—Part 2:Basic rules of tolerances, deviations and fits GB/T 1800.2-2009 Geometrical Product Specifications (GPS)—Limits and fits—Part 2:Tables of standard tolerance grades and limit deviations for holes and shafts GB/T 1800.2-2020 Geometrical product specifications(GPS)—ISO code system for tolerances on linear sizes—Part 2:Tables of standard tolerance classes and limit deviations for holes and shafts GB/T 1800.3-1998 Limits and fits—Bases—Part 3:Numerical values tables of standard tolerances and fundamental deviations GB/T 1800.4-1999 Limits and fits Tables of standard tolerance grades and limit deviations for holes and shafts GB/T 1801-1999 Limits and fits—Selection of tolerance zones and fits GB/T 1801-2009 Geometrical Product Specifications (GPS)—Limits and fits—Selection of tolerance zones and fits GB 1800~1804 GB/T 1803-2003 Limits and fits Tolerance zones for holes and shafts size up to 18mm GB/T 1804-2000 General tolerances for linear and angular dimensions without individual tolerance indications GB/T 1958-2004 Geometrical product Specifications(GPS)—Geometrical tolerance—Verification prescription GB/T 1958-2017 Geometrical Product Specifications(GPS)—Geometrical tolerance—Verification GB/T 2424.6-2006 Environmental testing for electric and electronic products—Confirmation of the performance of temperature/humidity chambers GB/T 2424.6-2021 Environmental testing—Part 3: Supporting documentation and guidance—Confirmation of the performance of temperature/humidity chambers GB/T 2424.7-2006 Environmental tests for electric and electronic products—Measurements in temperature chambers for tests A and tests B (with load) GB/T 2424.7-2024 Environmental testing—Part 3:Supporting documentation and guidance—Meas-urements in temperature chambers for tests A(Cold)and B(Dry heat)(with load) GB/T 2423.8-1995 Environmental testing for electric and electronic products—Parts 2:Test methods—Test Ed:Free fall GB/T 2423.10-1995 Environmental testing for electric and electronic products—Part 2:Test methods—Test Fc and guidance:Vibration (Sinusoidal) GB/T 2423.10-2008 Environmental testing for electric and electronic products—Part 2:Tests methods Test Fc:Vibration(sinusoidal) GB/T 2423.10-2019 Environmental testing—Part 2:Tests methods—Test Fc:Vibration(sinusoidal) GB/T 2828.1-2003 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection GB/T 2828.1-2012 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection GB/T 2828.2-2008 Sampling procedures for inspection by attributes—Part 2:Sampling plans indexed by limiting quality(LQ)for isolated lot inspection GB/T 2828.3-2008 Sampling procedures for inspection by attributes—Part 3:Skip-lot sampling procedures GB/T 2828.4-2008 Sampling procedures for inspection by attributes—Part 4:Procedures for assessment of declared quality levels GB/T 2828.5-2011 Sampling procedures for inspection by attributes—Part 5:System of sequential sampling plans indexed by acceptance quality limit(AQL)for lot-by-lot inspection GB/T 2828.10-2010 Sampling procedures for inspection by attributes—Part 10:Introduction to the GB/T 2828 series of standards for sampling for inspection by attributes GB/T 2828.11-2008 Sampling procedures for inspection by attributes—Part 11:Procedures for assessment of declared quality levels for small population GB/T 2829-2002 Sampling procedures and tables for periodic inspection by attributes (Apply to inspection of process stability) GB/T 2829-2025 Sampling procedures and tables for periodic inspection by attributes(Apply to inspection of process stability) GB/T 3047.1-1995 Series of basic dimensions of panels, rack and cabinets for vertical increment of 20mm GB/T 3047.2-1992 Series of basic dimensions of panels, racks and enclosures for vertical increment of 44.45mm GB/T 3047.3-2003 Series of basic dimensions of subracks and plug-in units for vertical increment of 20mm GB 3047.4 GB 4208-1993 Degrees of protection provided by enclosure (IP code) GB/T 4208-2008 Degrees of protection provided by enclosure(IP code) GB/T 4208-2017 Degrees of protection provided by enclosure(IP code) GB/T 8582-2000 Terminology for mechanical structures of electrotechnical and electronic equipment GB/T 8582-2008 Terminology for mechanical structures of electrotechnical and electronic equipment GB/T 10217-2011 The design guide of the outline and structure for the electric control equipment GB/T 10217-2021 Design guide of the outline and structure for the electric control equipment GB/T 10217-1988 The design guide of the outline and structurefor the electric control equipment GB/T 13384-1992 General specifications for packagings of mechanical and electrical products GB/T 13384-2008 General specifications for packing of mechanical and electrical product