GB/T 6595-1986
Replaced
GB/T 33319-2016
Active
National standards
GB/T 33319-2016 Plastics—Polyethylene compounds for breathable film
GB/T 33319-2016 Plastics—Polyethylene compounds for breathable film
Basic Information
Standard Code:
GB/T 33319-2016
Standard Type:
National standards
Standard Status:
Active
is_force_gb:
no
CCS Name:
Synthetic resins and plastics
ICS Name:
Thermoplastic plastics
Publish Date:
2016-12-13
Implement Date:
2017-07-01
Pages:
8 pages
Scope
This standard specifies the classification and naming, requirements, test methods, inspection rules, marking, packaging, transportation, and storage of polyethylene (PE) breathable film special materials.
This standard applies to polyethylene breathable film special materials made from polyethylene resin as the base material, with the addition of mineral fillers and other additives, which are formed by melt blending. Note: The breathable film referred to in this standard is a film obtained by longitudinal stretching at a certain temperature after the polyethylene (PE) breathable film special materials are extruded and cast into film by a cast film extruder or blown into film. A certain number of micropores are formed inside it, enabling it to have a breathable function.
Development Information
Referenced Standards
GB/T 1033.1-2008 Plastics—Methods for determining the density of non-cellular plastics—Part 1:Immersion method,liquid pyknometer method and titration method
GB/T 1037-1988 Test method for water vapor transmission of plastic film and sheet—Cup method
GB/T 1040.2-2006 Plastics—Determination of tensile properties—Part 2:Test conditions for moulding and extrusion plastics
GB/T 1844.1-2008 Plastics—Symbols and abbreviated terms—Part 1:Basic polymers and their special characteristics
GB/T 1845.2-2006 Plastics—Polyethylene(PE) moulding and extrusion materials—Part 2:Preparation of test specimens and determination of properties
GB/T 2547-2008 Plastic resins—Sampling
GB/T 3682-2000 Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
GB/T 6284-2006 Chemical products for industrial use—General method for determination of water content—The loss of mass on drying method
GB/T 9345.1-2008 Plastics—Determination of ash—Part 1:General methods
GB/T 17037.1-1997 Injection moulding of test specimens of thermoplastic materials—Part 1:General principles and moulding of multipurpose and bar test specimens
GB/T 31331-2014 Requirement and identification for environmental protection of modified plastics
GB/T 2918-1998 Plastics—Standard atmospheres for conditioning and testing
GB/T 2918-2018 Plastics—Standard atmospheres for conditioning and testing
GB/T 8170-1987 Rules for rounding off of numberical values
GB/T 8170-2008 Rules of rounding off for numerical values & expression and judgement of limiting values
GB 15979-2002 Hygienic standard for disposable sanitary products
GB 15979-2024 Hygienic requirements for disposable sanitary products
SH/T 1541-2006 Hot-melt plastic particle appearance test methods
Related Standards
GB/T 6598-1986
Active
GB/T 6598-1986 Determination of weight-average molecular weight of polystyrene standards by low angle laser light scattering method
GB/T 6599-1986
abolished_transferred
GB/T 6599-1986 Determination of molecular weight averages and molecular weight distribution of polystyrene standards by steric exclusion chromatography
GB/T 8330-1987
Replaced
GB/T 8330-1987 Method for the determination of true density of ion exchange resins in wet state
GB/T 8331-1987
Replaced
GB/T 8331-1987 Method for the determination of bulk density of ion exchange resins in wet state
GB/T 8324-1987
Replaced