GB/T 12360-1990 Replaced National standards

GB/T 12360-1990 Cone fit

Publish Date: 1990-06-14 Implement Date: 1991-05-01 For services related to genuine standard inquiry, procurement, translation, and other related services in China, please Contact Us

Basic Information

Standard Code: GB/T 12360-1990

Standard Type: National standards

Standard Status: Replaced

is_force_gb: no

CCS Name: Basic standards and general methods

ICS Name: Limits and coordination

Publish Date: 1990-06-14

Implement Date: 1991-05-01

Publisher: The National Technical Supervision Bureau

Technical Committee: The Mechanical Standards Research Institute of the Ministry of Machinery and Electronics Industry

Pages: 20 pages

Development Information

Drafting Persons:

Li Xiaopi, Yu Hanqing, Wu Jingxiang, and Gao Yanxin

Word Count: 30 Thousand words Pages: 20 pages

Superseded by the following standards

GB/T 12360-2005 Geometrical product specifications (GPS)—Cone fit

Referenced Standards

GB/T 157-2001 Geometrical product specifications(GPS) Series of conical tapers and taper angles GB/T 11334-1989 Cone tolerance GB/T 11334-2005 Geometrical Product Specifications(GPS)—Cone tolerance GB/T 1800.1-1997 Limits and fits—Bases—Part 1:Terminology GB/T 1800.1-2009 Geometrical Product Specifications (GPS)—Limits and fits—Part 1:Bases of tolerances,deviations and fits GB/T 1800.1-2020 Geometrical product specifications (GPS)—ISO code system for tolerances on linear sizes—Part 1:Basis of tolerances, deviations and fits GB/T 1800.2-1998 Limits and fits—Bases—Part 2:Basic rules of tolerances, deviations and fits GB/T 1800.2-2009 Geometrical Product Specifications (GPS)—Limits and fits—Part 2:Tables of standard tolerance grades and limit deviations for holes and shafts GB/T 1800.2-2020 Geometrical product specifications(GPS)—ISO code system for tolerances on linear sizes—Part 2:Tables of standard tolerance classes and limit deviations for holes and shafts GB/T 1800.3-1998 Limits and fits—Bases—Part 3:Numerical values tables of standard tolerances and fundamental deviations GB/T 1800.4-1999 Limits and fits Tables of standard tolerance grades and limit deviations for holes and shafts GB/T 1801-1999 Limits and fits—Selection of tolerance zones and fits GB/T 1801-2009 Geometrical Product Specifications (GPS)—Limits and fits—Selection of tolerance zones and fits GB/T 157-2025 Geometrical product specifications(GPS)—Series of conical tapers and taper angles GB/Z 157-2026 In vitro diagnostic test systems—Requirements and recommendations for detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) by nucleic acid amplification methods

Adopt standards

ISO 5166-82

Related Standards

GB/T 11334-1989 Replaced

GB/T 11334-1989 Cone tolerance

Publish Date: 1989-04-21

GB/T 1182-1996 Replaced

GB/T 1182-1996 Geometrical tolerancing—Generalities, definitions, symbols, indications on drawings

Publish Date: 1996-12-18

GB/T 1184-1996 Active

GB/T 1184-1996 Geometrical tolerancing—Geometrical tolerance for features without individual tolerance indications

Publish Date: 1996-12-18

GB/T 16671-1996 Replaced

GB/T 16671-1996 Geometrical tolerancing—Maximum material requirement, least material requirement and reciprocity requirement

Publish Date: 1996-12-18

GB/T 4249-1996 Replaced

GB/T 4249-1996 Tolerancing principle

Publish Date: 1996-12-18

GB/T 1800.1-1997 Replaced

GB/T 1800.1-1997 Limits and fits—Bases—Part 1:Terminology

Publish Date: 1997-03-04