MT 210-1990 The basic test methods for electrical products used in coal mine communication, detection, and control

GB 998 GB 5080.3 GB/T 531-1999 Rubber—Determination of indentation hardness by means of pocket hardness meters GB/T 531.1-2008 Rubber,vulcanized or thermoplastic—Determination of indentation hardness—Part 1:Duromerer method(Shore hardness) GB/T 531.2-2009 Rubber,vulcanized or thermoplastic—Determination of indentation hardness—Part 2:IRHD pocket meter method GB/T 1410-2006 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials GB/T 2423.1-2001 Environmental testing for electric and electronic products—Part 2:—Test methods Tests A:Cold GB/T 2423.1-2008 Environmental testing for electric and electronic products—Part 2:Test methods—Tests A:Cold GB/T 2423.2-2001 Environmental testing for electric and electronic products—Part 2:Test methods-Tests B:Dry heat GB/T 2423.2-2008 Environmental testing for electric and electronic products—Part 2:Test methods—Tests B:Dry heat GB/T 2423.3-1993 Basic environmental testing procedures for electric and electronic products—Test Ca:Damp heat, steady state GB/T 2423.3-2006 Environmental testing for electric and electronic products—Part 2:Testing method—Test Cab:Damp heat, steady state GB/T 2423.3-2016 Environmental testing—Part 2:Testing method—Test Cab:Damp heat,steady state GB/T 2423.4-1993 Basic environmental testing procedures for electric and electronic products—Test Db:Damp heat, cyclic GB/T 2423.4-2008 Environmental testing for electric and electronic products—Part 2:Test method—Test Db:Damp heat,cyclic(12 h+12 h cycle) GB/T 2423.5-1995 Environmental testing for electric and electronic products—Part 2:Test methods—Test Ea and guidance:Shock GB/T 2423.5-2019 Environmental testing—Part 2:Test methods—Test Ea and guidance:Shock GB/T 2423.8-1995 Environmental testing for electric and electronic products—Parts 2:Test methods—Test Ed:Free fall GB/T 2423.10-1995 Environmental testing for electric and electronic products—Part 2:Test methods—Test Fc and guidance:Vibration (Sinusoidal) GB/T 2423.10-2008 Environmental testing for electric and electronic products—Part 2:Tests methods Test Fc:Vibration(sinusoidal) GB/T 2423.10-2019 Environmental testing—Part 2:Tests methods—Test Fc:Vibration(sinusoidal) GB 3836.2-2000 Electrical apparatus for explosive gas atmospheres—Part 2:Flameproof enclosure “d” GB 3836.2-2010 Explosive atmospheres—Part 2:Equipment protection by flameproof enclosures "d" GB/T 3836.2-2021 Explosive atmospheres—Part 2:Equipment protection by flameproof enclosures “d” GB 3836.4-2000 Electrical apparatus for explosive gas atmospheres—Part 4:Intrinsic safety“i” GB 3836.4-2010 Explosive atmospheres—Part 4:Equipment protection by intrinsic safety "i" GB/T 3836.4-2021 Explosive atmospheres—art 4:Equipment protection by intrinsic safety “i” GB/T 4942.2-1993 Degrees of protection provided by enclosures for low-voltage apparatus GB/T 5080.1-1986 Equipment reliability testing—General requirements GB/T 5080.1-2012 Reliability testing—Part 1:Test conditions and statistical test principles GB/T 5080.2-1986 Equipment reliability testing—Guidance for the design of test cycles GB/T 5080.2-2012 Reliability testing—Part 2:Design of test cycles GB/T 5080.4-1985 Equipment reliability testing—Procedure for point estimates and confidence intervals from reliability determination tests(Exponental distribution) GB/T 5080.5-1985 Equipment reliability testing—compliance test plans for success ratio GB/T 5080.6-1996 Equipment reliability testing—Tests for the validity of a constant failure rate assumption GB/T 5080.7-1986 Equipment reliability testing Compliance test plans for failure rate and mean time between failures assuming constant failure rate GB/T 6379-1986 Precision of test methods Determination of repeatability and reproducibility for a standard test method by interlaboratory tests GB/T 6379.1-2004 Accuracy(trueness and precision)of measurement methods and results—Part 1:General principles and definitions GB/T 6379.2-2004 Accuracy(trueness and precision)of measurement methods and results—Part 2:Basic method for the determination of repeatability and reproducibility of a standard measurement method GB/T 6379.3-2012 Accuracy(trueness and precision)of measurement methods and results—Part 3:Intermediate measures of the precision of a standard measurement method GB/T 6379.4-2006 Accuracy (trueness and precision) of measurement methods and results—Part 4:Basic methods for the determination of the trueness of a standard measurement method GB/T 6379.5-2006 Accuracy (trueness and precision) of measurement methods and results—Part 5:alternative methods for the determination of the precision of a standard measurement method GB/T 6379.6-2009 Accuracy(trueness and precision)of measurement methods and results—Part 6:Use in practice of accuracy values MT 209-1990 The general technical requirements for electrical products used in coal mine communication, detection, and control GB/T 6379.4-2025 Accuracy(trueness and precision)of measurement methods and results—Part 4:Basic methods for the determination of the trueness of a standard measurement method