GB/T 17187-1997
Replaced
GB/T 25409-2025
Active
National standards
GB/T 25409-2025 Small-size submersible motor-pumps
GB/T 25409-2025 Small-size submersible motor-pumps
Basic Information
Standard Code:
GB/T 25409-2025
Standard Type:
National standards
Standard Status:
Active
is_force_gb:
no
CCS Name:
Agricultural machinery and equipment
ICS Name:
Irrigation and drainage equipment
Publish Date:
2025-10-31
Implement Date:
2026-05-01
Pages:
36 pages
Scope
This document specifies the types, models, and basic parameters of small submersible electric pumps, technical requirements, inspection rules, marking, packaging, transportation, and storage, and describes the corresponding test methods.
This document is applicable to small submersible electric pumps with a rated power of less than or equal to 22 kW for conveying clean water.
Development Information
Replace the following standards
Referenced Standards
GB/T 191-2000 Packaging—Pictorial marking for handling of goods
GB/T 191-2008 Packaging—Pictorial marking for handling of goods
GB/T 191-2025 Graphical symbols marking for handling and storage of packages
GB 755-2000 Rotating electrical machines—Rating and performance
GB/T 755-2008 Rotating electrical machines—Rating and performance
GB/T 755-2019 Rotating electrical machines—Rating and performance
GB/T 755-2025 Rotating electrical machines—Rating and performance
GB/T 755.2-2003 Methods for determining losses and efficiency of rotating electrical machinery from tests(excluding machines for traction vehicles)
GB 1971-1980 Terminal markings and direction of rotation of rotating electrical machines
GB/T 1971-2006 Rotating electrical machines—Terminal markings and direction of rotation
GB/T 1971-2021 Rotating electrical machines—Terminal markings and direction of rotation
GB/T 2828.1-2003 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection
GB/T 2828.1-2012 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection
GB/T 4942-2021 Degrees of protection provided by the integral design of rotating electrical machines(IP code)—Classification
GB 5013.4-1997 Rubber insulated cables of rated voltages up to and including 450/750V—Part 4:Cords and flexible cables
GB/T 5013.4-2008 Rubber insulated cables of rated voltages up to and including 450/750 V—Part 4:Cords and flexible cables
GB/T 9239.1-2006 Mechanical vibration—Balance quality requirements for rotors in a constant(rigid)state—Part 1:Specification and verification of balance tolerances
GB 10395.8-2006 Tractors and machinery for agriculture and forestry—Technical means for ensuring safety—Part 8:Irrigation pumps and machines
GB 10396-1999 Tractors,machinery for agriculture and forestry,powered lawn and garden equipment—Safety signs and hazard pictorials—General principles
GB 10396-2006 Tractors,machinery for agriculture and forestry,powered lawn and garden equipment—Safety signs and hazard pictorials—General principles
GB/T 12785-2014 Test methods for submersible motor-pumps
GB/T 13306-1991 Plates
GB/T 13306-2011 Plates
GB 18613-2020 Minimum allowable values of energy efficiency and values of efficiency grades for motors
JB/T 5673-2015 JBT 5673-2015 Agricultural and Forestry Tractors and Machinery Coating General Technical Specification
JB/T 6880.1-2013 Pump Grey Iron Pump Component
JB/T 6880.1-1993 Pumping gray iron parts
JB/T 6880.2-2021 JBT 6880.2-2021 Castings for Pumps Part 2: Cast Steel Pumps for Pumps
JB/T 6880.2-1993 Pump cast steel parts
JB/T 6880.3-2014 Pump castings - Part 3: Anti-wear abrasion resistant white cast iron for pumps
JB/T 6880.3-1993 Pump anti-wear white cast iron parts
JB/T 8735.2-2016 Rated voltage 450/750 V and below rubber insulated flexible wire and flexible cable Part 2: General rubber insulated flexible cable
JB/T 8735.2-2011 JBT 8735.2-2011 Rated voltage 450/750 V and below rubber insulated soft wire and cables Part 2: General rubber-sheathed soft cables
JB/T 8735.2-1998 Rubber insulated cords and flexible cables of rated voltages up to and including 450/750V Part 2:Tough rubber sheathed flexible cables for general purposes
JB/T 8735.3-2016 Rubber-insulated flexible wires and cables with a rated voltage of 450/750 V and below - Part 3: Rubber-insulated braided flexible cables
JB/T 8735.3-2011 Rated voltage 450/750 V and below rubber insulated soft wire and soft cable Part 3: Rubber insulated braided soft wire. Note: JB/T is the abbreviation of standard reference, while 8735.3 is the standard code number. The word "rubber" refers to rubber insulation. "Braided" refers to a woven structure, usually used for insulation of electrical wires and cables. The phrase "450/750 V and below" indicates the rated voltage range of the wire or cable
JB/T 8735.3-1998 Rubber insulated cords and flexible cables of rated voltages up to and including 450/750V Part 3:Rubber insulated braided cords
JB/T 11923-2014 Assessment and evaluation method for reliability of submersible electric pumps
Related Standards
GB/T 17188-1997
Replaced
GB/T 17188-1997 Agricultural irrigation equipment—Emitting-pipe systems—Specification and test methods
GB/T 18025-2000
Active
GB/T 18025-2000 Agricultural irrigation—Wiring and equipment for electrically driven or controlled irrigation machines
GB/T 12785-2002
Replaced
GB/T 12785-2002 Test methods for submersible motor-pumps
GB/T 18687-2002
Replaced
GB/T 18687-2002 Agricultural irrigation equipment—Sprayers—General requirements and test method
GB/T 18688-2002
Replaced