GB/T 4133-1984
Replaced
GB/T 14230-2021
Active
National standards
GB/T 14230-2021 Test method of tooth bending strength for gear load capacity
GB/T 14230-2021 Test method of tooth bending strength for gear load capacity
Price:
$ 113
Basic Information
Standard Code:
GB/T 14230-2021
Standard Type:
National standards
Standard Status:
Active
is_force_gb:
no
CCS Name:
Gears and gear transmissions
ICS Name:
Gears and gear transmissions
Publish Date:
2021-05-21
Implement Date:
2021-12-01
Pages:
35 pages
Scope
This document specifies the principles, objectives, types, methods, equipment, failure criteria, procedures, data processing, and test reports for the bending fatigue strength test of involute cylindrical gears. This document is applicable to determining the basic data required for the design of the bending fatigue bearing capacity of involute cylindrical gears made of steel or cast iron, and is also suitable for comparing and analyzing the bending fatigue performance of gears under different materials, different processes, and different modification methods. Similar tests for gears made of other materials or non-involute gears can be used as reference.
Development Information
Replace the following standards
Referenced Standards
GB/T 1356-2001 Cylindrical gears for general and heavy engineering—Standard basic rack tooth profile
GB/T 3358.1-1993 Terms for statistics—Part 1:Terms for general statistics
GB/T 3358.1-2009 Statistics—Vocabulary and symbols—Part 1:General statistical terms and terms used in probability
GB/T 3480.1-2019 Calculation of load capacity of spur and helical gears—Part 1:Basic principles,introduction and general influence factors
GB/T 3480.3-2021 Calculation of load capacity of spur and helical gears—Part 3:Calculation of tooth bending strength
GB/T 10095.1-2001 Cylindrical gears—system of accuracy—Part 1:Definitions and allowable values of deviations relevant to corresponding flanks of gear teeth
GB/T 10095.1-2008 Cylindrical gears—System of accuracy—Part 1:Definitions and allowable values of deviations relevant to corresponding flanks of gear teeth
GB/T 10095.1-2022 Cylindrical gears—ISO system of flank tolerance classification—Part 1:Definitions and allowable values of deviations relevant to flanks of gear teeth
GB/T 10095.2-2001 Cylindrical gears-system of accuracy—Part 2:Definitions and allowable values of deviations relevant to radial composite deviations and runout information
GB/T 10095.2-2008 Cylindrical gears—System of accuracy—Part 2:Definitions and allowable values of deviations relevant to radial composite deviations and runout information
GB/T 10095.2-2023 Cylindrical gears—ISO system of flank tolerance classification—Part 2:Definitions and allowable values of double flank radial composite deviations
GB/T 25917.1-2019 Uniaxial fatigue testing systems—Part 1:Calibration of dynamic force
JB/T 8831-2001 The lubrication oil for industrial closed-gear should be selected based on several factors, including the type of gear, its operating conditions, and the expected wear and tear. Generally, the following are the most commonly used oils for closed-gear: mineral oil, grease, and synthetic lubricants. When selecting the appropriate lubricant for your specific application, it is recommended to consult with a professional who is familiar with the equipment you are using
JB/T 8831-2024 Lubricant selection method for closed gears in industrial environment JB/T 8831-2024
Related Standards
GB/T 6404-1986
Replaced
GB/T 6404-1986 Determination of sound power level for noise emitted by gear units
GB 6413-1986
Abolished
GB 6413-1986 Calculation of scuffing load capacity for involute cylindrical gears
GB/T 6443-1986
Replaced
GB/T 6443-1986 Involute cylindrical gears-Information of the dimensional data to be given on the drawing
GB/T 1357-1987
Replaced
GB/T 1357-1987 Modules of involute cylindrical gears
GB/T 8543-1987
Replaced