Standards

CJ/T 197-2004 Replaced

CJ/T 197-2004 The corrugated hose assemblies of stainless for gas

This standard specifies the terms and definitions, specifications, type classification, and model marking, requirements, marking and labeling, as well as packaging, transportation, and storage of stainless steel corrugated hoses for gas use (hereinafter referred to as hoses).
This standard applies to hoses used for connecting gas appliances, gas meters, and gas pipelines with a nominal diameter of less than or equal to 50 mm and a nominal pressure of less than or equal to 0.1 MPa, hoses used inside gas appliances, and buried hoses (hereinafter referred to as buried pipes).

Publish Date: 2004-12-02

CJ/T 199-2004 Replaced

CJ/T 199-2004 Stainless steel supphy-exhaust pipe for burning equipment

This standard specifies the model codes, types, requirements, test methods, inspection rules, markings, packaging, transportation, and storage of stainless steel exhaust pipes used in gas-fired appliances (hereinafter referred to as exhaust pipes).
This standard applies to stainless steel exhaust pipes used in natural and forced ventilation-type gas-fired appliances that are fueled by liquefied petroleum gas, natural gas, artificial coal gas, and petroleum.

Publish Date: 2004-12-02

CJ/T 200-2004 Replaced

CJ/T 200-2004 Preformed directly buried steam insulating pipes technical-specification for heating in city

This standard specifies the basic structure, materials, performance, test methods, and inspection rules of prefabricated direct-buried steam insulation pipes for urban heating (hereinafter referred to as steam insulation pipes), as well as requirements for product marking, transportation, and storage.
This standard applies to the prefabrication and inspection of steam insulation pipes with a transmission medium temperature of less than or equal to 350℃ and an operating pressure of no more than 1.6 MPa.

Publish Date: 2004-12-02

CJ/T 51-2004 Replaced

CJ/T 51-2004 Methods for the examination of municipal sewage

This chapter specifies the method of determining the pH value of urban wastewater using a potentiometer.
Measurement range: 1.0～13.0.

Publish Date: 2004-12-02

CJ/T 194-2004 Replaced

CJ/T 194-2004 Non-contact water supply device

This standard specifies the product classification, technical requirements, test methods, inspection rules, and marking, packaging, transportation, and storage of non-contact water supply appliances (hereinafter referred to as "water supply appliances").
This standard applies to the manufacture and acceptance of water supply appliances.

Publish Date: 2004-09-17

CJ/T 192-2004 Replaced

CJ/T 192-2004 Composite steel pipe stainless steel lined

This standard specifies the marking, requirements, dimensions, test methods, inspection rules, labeling, packaging, transportation, and storage of stainless steel composite steel pipes (referred to as composite pipes) produced by composite processes such as reducing diameter, cold expansion, detonation, or brazing methods.
This standard applies to composite steel pipes with a working pressure not exceeding 2.0 MPa and a nominal diameter not exceeding 500 mm, which are used for conveying low-pressure fluids such as cold and hot water, drinking water, fire water supply, gas, air, oil, and steam, or for other purposes.

Publish Date: 2004-04-30

CJ/T 190-2004 Replaced

CJ/T 190-2004 Polyethlene/aluminum/polyethylene composite pipe press fitting

This standard specifies the definition, classification, requirements, test methods, inspection rules, marking, packaging, transportation, and storage of crimped fittings for aluminum-plastic composite pipes (referred to as fittings).
This standard applies to aluminum-plastic pipes (referred to as pipes) used with crimped fittings for conveying fluids (cold water, drinking water distribution systems for cold and hot water, water supply and distribution systems, heating systems, underground irrigation systems, industrial special fluids, compressed air, gas, etc.) under the maximum allowable working pressure specified in GB/T 18997.1—2003 "Aluminum-Plastic Composite Pressure Pipes—Part 1: Aluminum-Plastic Pipes with Overlapped Welded Aluminum Tubes".
Crimped fittings for aluminum-plastic composite pipes with overlapped welded aluminum tubes and crimped fittings for cross-linked polyethylene plastic pipes can refer to this standard.

Publish Date: 2004-03-25

CJ/T 28-2003 Replaced

CJ/T 28-2003 Chinese cooking gas applianes

This standard specifies the definition, classification, basic parameters, structural requirements, technical requirements, test methods, and marking, packaging, storage, and transportation of Chinese-style gas cooking stoves (hereinafter referred to as cooking stoves).
This standard applies to Chinese-style gas cooking stoves with a rated heat flow of less than or equal to 60kW.

Publish Date: 2003-12-05

CJ/T 29-2003 Replaced

CJ/T 29-2003 Water boiling gas appliances

This standard specifies the model designation method, technical requirements, test methods, inspection rules, marking, packaging, transportation, and storage for fixed-pressure gas boilers for boiling water.
This standard applies to fixed-pressure gas boilers for boiling water (hereinafter referred to as boilers) used for producing drinking water with a rated heat flow of less than 100 kW.

Publish Date: 2003-12-05

CJ/T 186-2003 Replaced

CJ/T 186-2003 Floor drain

This standard specifies the product classification and marking, requirements, test methods, inspection rules and marking, packaging, and storage and transportation of floor drains.
This standard applies to floor drains used in industrial and civil buildings, but not to special floor drains used in places such as civil air defense projects.

Publish Date: 2003-10-16

CJ/T 183-2003 Replaced

CJ/T 183-2003 Plastic-steel-plastic composite pressure pipe

This standard specifies the definition, classification, and marking of steel-plastic composite pressure pipes (hereinafter referred to as composite pipes), their requirements, test methods, inspection rules and markings, product user manuals, packaging, transportation, and storage.
This standard applies to composite pipes used for the transportation of cold and hot water, drinking water, heating, urban gas, and special fluids (including industrial wastewater, corrosive gases, solid powders, etc.) in towns and buildings.

Publish Date: 2003-07-11

CJ/T 184-2003 Replaced

CJ/T 184-2003 Stainless steel-plastic composite pipes

This standard specifies the classification and naming, requirements, test methods, inspection rules, marking, user manuals, packaging, transportation, and storage of stainless steel plastic composite pipes.
This standard applies to stainless steel plastic composite pipes made by extrusion-molded plastic pipes as the inner layer and butt-welded thin-walled stainless steel pipes as the outer layer, which are bonded together by hot melt adhesive or other adhesives. These composite pipes (hereinafter referred to as "composite pipes") are used for the transportation of cold and hot water, gas, compressed air, and industrial fluids in buildings, with a nominal pressure of 1.6 MPa.

Publish Date: 2003-07-11