NY/T 259-1994 Hemp twister machine

NY/T 259-2009 Lianhe machine for processing sisal fibers

GB 1183 GB 1300 GB 1802 GB/T 985-1988 Basic forms and sizes of weld grooves for gas welding manual arc welding and gas-Shielded arc welding GB/T 985.1-2008 Recommended joint preparation for gas welding,manual metal arc welding,gas-shield arc welding and beam welding GB/T 985.2-2008 Recommended joint preparation for submerged arc welding GB/T 985.3-2008 Recommended joint preparation for gas-shield arc welding on aluminium and its alloys GB/T 985.4-2008 Recommended joint preparation for welding on clad steels GB/T 1182-1996 Geometrical tolerancing—Generalities, definitions, symbols, indications on drawings GB/T 1182-2008 Geometrical Product Specifications(GPS)—Geometrical tolerancing—Tolerances of form, orientation, location and run-out GB/T 1182-2018 Geometrical product specifications(GPS)—Geometrical tolerancing—Tolerances of form,orientation,location and run-out GB/T 1184-1996 Geometrical tolerancing—Geometrical tolerance for features without individual tolerance indications GB/T 1800.1-1997 Limits and fits—Bases—Part 1:Terminology GB/T 1800.1-2009 Geometrical Product Specifications (GPS)—Limits and fits—Part 1:Bases of tolerances,deviations and fits GB/T 1800.1-2020 Geometrical product specifications (GPS)—ISO code system for tolerances on linear sizes—Part 1:Basis of tolerances, deviations and fits GB/T 1800.2-1998 Limits and fits—Bases—Part 2:Basic rules of tolerances, deviations and fits GB/T 1800.2-2009 Geometrical Product Specifications (GPS)—Limits and fits—Part 2:Tables of standard tolerance grades and limit deviations for holes and shafts GB/T 1800.2-2020 Geometrical product specifications(GPS)—ISO code system for tolerances on linear sizes—Part 2:Tables of standard tolerance classes and limit deviations for holes and shafts GB/T 1800.3-1998 Limits and fits—Bases—Part 3:Numerical values tables of standard tolerances and fundamental deviations GB/T 1800.4-1999 Limits and fits Tables of standard tolerance grades and limit deviations for holes and shafts GB/T 1801-1999 Limits and fits—Selection of tolerance zones and fits GB/T 1801-2009 Geometrical Product Specifications (GPS)—Limits and fits—Selection of tolerance zones and fits GB/T 1803-2003 Limits and fits Tolerance zones for holes and shafts size up to 18mm GB/T 1804-2000 General tolerances for linear and angular dimensions without individual tolerance indications GB/T 2828.1-2003 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection GB/T 2828.1-2012 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection GB/T 2828.2-2008 Sampling procedures for inspection by attributes—Part 2:Sampling plans indexed by limiting quality(LQ)for isolated lot inspection GB/T 2828.3-2008 Sampling procedures for inspection by attributes—Part 3:Skip-lot sampling procedures GB/T 2828.4-2008 Sampling procedures for inspection by attributes—Part 4:Procedures for assessment of declared quality levels GB/T 2828.5-2011 Sampling procedures for inspection by attributes—Part 5:System of sequential sampling plans indexed by acceptance quality limit(AQL)for lot-by-lot inspection GB/T 2828.10-2010 Sampling procedures for inspection by attributes—Part 10:Introduction to the GB/T 2828 series of standards for sampling for inspection by attributes GB/T 2828.11-2008 Sampling procedures for inspection by attributes—Part 11:Procedures for assessment of declared quality levels for small population GB/T 3768-1996 Acoustics—Determination of sound power levels of noise sources using sound pressure—Survey method using an enveloping measurement surface over a reflecting plane GB/T 3768-2017 Acoustics—Determination of sound power levels and sound energy levels of noise sources using sound pressure—Survey method using an enveloping measurement surface over a reflecting plane GB/T 5117-1995 Carbon steel covered electrodes GB/T 5117-2012 Covered electrodes for manual metal arc welding of non-alloy and fine grain steels GB/T 8196-2003 Safety of machinery—Guards—General requirements for the design and construction of fixed and movable guards GB/T 8196-2018 Safety of machinery—Guards—General requirements for the design and construction of fixed and movable guards GB/T 10095.1-2001 Cylindrical gears—system of accuracy—Part 1:Definitions and allowable values of deviations relevant to corresponding flanks of gear teeth GB/T 10095.1-2008 Cylindrical gears—System of accuracy—Part 1:Definitions and allowable values of deviations relevant to corresponding flanks of gear teeth GB/T 10095.1-2022 Cylindrical gears—ISO system of flank tolerance classification—Part 1:Definitions and allowable values of deviations relevant to flanks of gear teeth GB/T 10095.2-2001 Cylindrical gears-system of accuracy—Part 2:Definitions and allowable values of deviations relevant to radial composite deviations and runout information GB/T 10095.2-2008 Cylindrical gears—System of accuracy—Part 2:Definitions and allowable values of deviations relevant to radial composite deviations and runout information GB/T 10095.2-2023 Cylindrical gears—ISO system of flank tolerance classification—Part 2:Definitions and allowable values of double flank radial composite deviations