Current Category: CN-TSG - Special Equipment Standards
The design, manufacture, modification, repair, and use of site vehicles, as well as their inspection, shall comply with the provisions of these regulations.
本规则适用于《电梯型式试验产品目录》(见附件A,以下简称《目录》)所列产品的型式试验。《目录》所列产品有下列情况之一的,应当进行型式试验:(1)制造单位首次制造或者境外制造在境内首次投入使用的;(2)产品主要参数超出适用范围的;(3)产品型式试验要求中规定的产品配置发生变更的;(4）出现其他影响产品安全性能,国家质量监督检验检疫总局(以下简称国家质检总局)提出型式试验要求的
This rule applies to the regular inspection and initial inspection of lifting machinery within the scope of the "Special Equipment Catalogue". The scope of lifting machinery subject to initial inspection is in accordance with the "Catalogue of Lifting Machinery Subject to Initial Inspection" (see Annex A). For large-scale lifting machinery installed with a safety monitoring management system, the specific scope is in accordance with the "Catalogue of Large-scale Lifting Machinery Installed with a Safety Monitoring Management System" (see Annex B), and the initial inspection items shall include the relevant content of the safety monitoring management system. For the following cranes in Annex B, the regular inspection shall include the relevant content of the safety monitoring management system: (1) Those that have undergone supervision inspection in accordance with the requirements of the "Rules for Supervision and Inspection of Major Installation, Modification and Repair of Lifting Machinery" (TSG Q7016); (2) Those that have undergone initial inspection in accordance with the requirements of this rule; and (3) Those that meet the requirements of Article 23 of this rule.
The amendment of these rules adds requirements related to large-scale lifting machinery safety monitoring and management systems and simple elevators, refines the requirements for special safety protection and protective devices of lifting machinery, adjusts the scope of supervision and inspection, improves the judgment principles of supervision and inspection conclusions, and updates relevant content. It provides a basis for better guiding and regulating the installation, modification, and major repair supervision and inspection of lifting machinery
This rule applies to the supervision and inspection work of boiler manufacturing, installation, modification, and major repairs required by the "Boiler Safety Technical Supervision Regulations" (hereinafter referred to as the "Boiler Regulations") used within the territory of the People's Republic of China.
This rule applies to the regular inspection of boilers as required by the "Boiler Safety Technical Supervision Regulations" (hereinafter referred to as the "Boiler Regulations")
本规则适用于《中华人民共和国特种设备安全法》《特种设备安全监察 条例》规定的为特种设备生产、经营、使用提供无损检测服务的机构的核准,核准项目见《特种设备无损检测核准项目分类表》(附录A)
This regulation applies to seamless gas cylinders, welded gas cylinders, welded insulated gas cylinders, wrapped gas cylinders, gas cylinders with internal packing, and gas cylinder accessories used in normal environmental temperatures (-40°C to 60°C, Note 1-1) with a nominal volume of 0.4L to 3000L and a nominal working pressure of 0.2MPa to 35MPa (gauge pressure, same below) and a product of pressure and volume greater than or equal to 1.0MPa·L, for storing compressed gases, high (low) pressure liquefied gases, low-temperature liquefied gases, dissolved gases, adsorbed gases, liquids with a standard boiling point equal to or lower than 60°C, and mixed gases (two or more gases). Fire extinguisher gas cylinders and large-capacity gas cylinders used in fire-fighting vehicles, long-tube trailers, and tube-type containers, or for storing electronic gases, shall comply with the design, manufacture, and materials specified in this regulation. The main types of gas cylinders covered by this regulation, their designations, and corresponding product standards are listed in Annex A. For gas cylinder accessories within the scope of application specified in Section 1.2 of this regulation, in addition to complying with this regulation, they shall also comply with the provisions of the "Safety Technical Supervision Regulations for Gas Cylinder Accessories" (TSG RF001). For vehicle gas cylinders (Note 1-2), in addition to complying with this regulation, they shall also comply with the provisions of the "Safety Technical Supervision Regulations for Vehicle Gas Cylinders" (TSG R0009). This regulation does not apply to fire extinguisher gas cylinders that only withstand instantaneous pressure during fire suppression and do not withstand pressure during storage, fixed-use cylindrical pressure vessels, and gas cylinders used in military equipment, nuclear facilities, aerospace vehicles, railway locomotives, maritime facilities, and ships, or specialized equipment for civil airports. T
This rule applies to the use and management of boilers within the scope of the "Special Equipment Safety Law of the People's Republic of China".
本规则适用于《特种设备安全监察条例》范围内的固定式压力容器、移动式压力容器的氧舱,但是不包括气瓶
本规则适用于《办法》所规定的特种备作业人员(以下简称作业人员)的考核工作。作业人员的具体作业种类与项目按照《特种设备作业人员作业种类与项目》(以下简称《项目》)规定