GB 15065-1994 Black polyethylene compounds for wire and cable

GB/T 15065-2009 Black polyethylene compounds for wire and cable

GB 2951.36 GB 2951.37 GB 2951.39 GB/T 1033-1986 Test method for density and relative density of plastics GB/T 1033.1-2008 Plastics—Methods for determining the density of non-cellular plastics—Part 1:Immersion method,liquid pyknometer method and titration method GB/T 1033.2-2010 Plastics—Methods for determining the density of non-cellular plastics—Part 2:Density gradient column method GB/T 1033.3-2010 Plastics—Methods for determining the density of non-cellular plastics—Part 3:Gas pyknometer method GB/T 1040.1-2006 Plastics—Determination of tensile properties—Part 1:General principles GB/T 1040.1-2018 Plastics—Determination of tensile properties—Part 1:General principles GB/T 1040.2-2006 Plastics—Determination of tensile properties—Part 2:Test conditions for moulding and extrusion plastics GB/T 1040.2-2022 Plastics—Determination of tensile properties—Part 2:Test conditions for moulding and extrusion plastics GB/T 1040.3-2006 Plastics—Determination of tensile properties—Part 3:Test conditions for films and sheets GB/T 1040.4-2006 Plastics—Determination of tensile properties—Part 4:Test conditions for isotropic and orthotropic fibre-reinforced plastic composites GB/T 1040.5-2008 Plastics—Determination of tensile properties—Part 5:Test conditions for unidirectional fibre-reinforced plastic composites GB/T 1408.1-1999 Methods of test for electric strength of solid insulating materials-Tests at power frequencies GB/T 1408.1-2006 Electrical strength of insulating materials—Test methods—Part 1:Tests at power frequencies GB/T 1408.1-2016 Insulating materials—Test methods for electric strength—Part 1:Test at power frequencies GB/T 1408.2-2006 Electrical strength of insulating materials—Test methods—Part 2:Additional requirements for tests using direct voltage GB/T 1408.2-2016 Insulating materials—Test methods for electric strength—Part 2:Additional requirements for tests using direct voltage GB/T 1408.3-2007 Electric strength of insulating materials—Test methods—Part 3:Additional requirements for 1.2/50 μs impulse tests GB/T 1408.3-2016 Insulating materials—Test methods for electric strength—Part 3:Additional requirements for 1.2/50μs impulse tests GB/T 1409-2006 Recommended methods for the determination of the permittivity and dielectric dissipation fator of electrical insulating materials at power,audio and radio frequencies including meter wavelengths GB/T 1410-2006 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials GB/T 1633-2000 Plastics—Thermoplastic materials—Determination of Vicat softening temperature(VST) GB/T 2828.1-2003 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection GB/T 2828.1-2012 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection GB/T 2828.2-2008 Sampling procedures for inspection by attributes—Part 2:Sampling plans indexed by limiting quality(LQ)for isolated lot inspection GB/T 2828.3-2008 Sampling procedures for inspection by attributes—Part 3:Skip-lot sampling procedures GB/T 2828.4-2008 Sampling procedures for inspection by attributes—Part 4:Procedures for assessment of declared quality levels GB/T 2828.5-2011 Sampling procedures for inspection by attributes—Part 5:System of sequential sampling plans indexed by acceptance quality limit(AQL)for lot-by-lot inspection GB/T 2828.10-2010 Sampling procedures for inspection by attributes—Part 10:Introduction to the GB/T 2828 series of standards for sampling for inspection by attributes GB/T 2828.11-2008 Sampling procedures for inspection by attributes—Part 11:Procedures for assessment of declared quality levels for small population GB/T 2951.7-1997 Common test methods for insulating and sheathing materials of electric cables Part 3:Methods specific to PVC compounds Swction two:Loss of mass test—Thermal stability test GB/T 2951.13-2008 Common test methods for insulating and sheathing materials of electric and optical cables—Part 13:Methods for general application—Measurement for determining the density—Water absorption tests—Shrinkage test GB/T 3682-2000 Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics GB/T 3682.1-2018 Plastics—Determination of the melt mass-flow rate(MFR)and melt volume-flow rate(MVR)of thermoplastics—Part 1:Standard method GB/T 3682.2-2018 Plastics—Determination of the melt mass-flow rate(MFR)and melt volume-flow rate(MVR)of thermoplastics—Part 2:Method for materials sensitive to time-temperature history and/or moisture GB/T 5470-1985 Test method for brittleness temperature of plastics by impact GB/T 5470-2008 Plastics—Determination of the brittleness temperature by impact GB/T 9352-1988 Plastics—Compression moulding test specimens of thermoplastic materials GB/T 9352-2008 Plastic—Compression moulding of test specimens of thermoplastic materials GB 12527-1990 Aerial insulated cables of rated voltages up to and including 1 kV GB/T 12527-2008 Aerial insulated cables for rated voltages up to and including 1 kV GB/T 1040.1-2025 Plastics—Determination of tensile properties—Part 1:General principles GB/T 1633-2025 Plastics—Thermoplastic materials—Determination of Vicat softerning temperature(VST)

IEC 502-1983