中文 English
GB/T 26168.2-2010 Replaced National standards

GB/T 26168.2-2010 Electrical insulating materials—Determination of the effects of ionizing radiation—Part 2:Procedures for irradiation and test

GB/T 26168.2-2010 Electrical insulating materials—Determination of the effects of ionizing radiation—Part 2:Procedures for irradiation and test

Publish Date: 2011-01-14 Implement Date: 2011-07-01 For services related to genuine standard inquiry, procurement, translation, and other related services in China, please Contact Us

Basic Information

Standard Code: GB/T 26168.2-2010
Standard Type: National standards
Standard Status: Replaced
is_force_gb: no
CCS Name: Electrician's insulating materials and their products
ICS Name: Plastic and rubber insulation materials
Publish Date: 2011-01-14
Implement Date: 2011-07-01
Pages: 17 pages

Scope

This part of GB/T 26168 specifies the irradiation conditions that should be maintained before, during, and after irradiating insulating materials with ionizing radiation to determine any physical or chemical changes induced by radiation. It proposes several irradiation conditions that may have important application value and lists various parameters that may affect radiation-induced reactions under these conditions.
This part is applicable to selecting suitable samples, irradiation conditions, and test methods to facilitate determining the significance of radiation's impact on performance. Since many materials are used in air or inert gas environments, standard irradiation conditions are provided for these two situations. Appendix A of this part also provides examples of test reports for several materials.
This part is not applicable to measurements during irradiation.

Development Information

Word Count: 32 Thousand words Pages: 17 pages

Same series standard

GB/T 26168.1-2010 Electrical insulating materials—Determination of the effects of ionizing radiation—Part 1: Radiation interaction and dosimetry GB/T 26168.3-2010 Electrical insulating materials—Determination of the effects of ionizing radiation—Part 3:Classification system for service in radiation environments GB/T 26168.4-2010 Electrical insulating materials—Determination of the effects of ionizing radiation—Part 4:Procedures for assessment of ageing in service

Superseded by the following standards

GB/T 26168.2-2018 Electrical insulating materials—Determination of the effects of ionizing radiation—Part 2:Procedures for irradiation and test

Referenced Standards

GB/T 528-2009 Rubber,vulcanized or thermoplastic—Determination of tensile stress-strain properties GB/T 1043.1-2008 Plastics—Determination of charpy impact properties—Part 1:Non-instrumented impact test GB/T 1408.1-2006 Electrical strength of insulating materials—Test methods—Part 1:Tests at power frequencies GB/T 1410-2006 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials GB/T 2411-2008 Plastics and ebonite—Determination of indentation hardness by means of a durometer(shore hardness) GB/T 6031-1998 Rubber,vulcanized or thermoplastic—Determination of hardness (hardness between 10 IRHD and 100IRHD) GB/T 7759-1996 Rubber, Vulcanized or thermoplastic—Determination of compression set at ambient elevated or low temperatures GB/T 9341-2008 Plastics—Determination of flexural properties GB/T 10064-2006 Methods of test for the determination of the insulation resistance of solid insulating materials GB/T 10580-2003 Standard conditions for use prior to and during the testing of solid insulating materials GB/T 26168.1-2010 Electrical insulating materials—Determination of the effects of ionizing radiation—Part 1: Radiation interaction and dosimetry GB/T 26168.3-2010 Electrical insulating materials—Determination of the effects of ionizing radiation—Part 3:Classification system for service in radiation environments GB/T 1040.1-2006 Plastics—Determination of tensile properties—Part 1:General principles GB/T 1040.1-2018 Plastics—Determination of tensile properties—Part 1:General principles GB/T 1040.2-2006 Plastics—Determination of tensile properties—Part 2:Test conditions for moulding and extrusion plastics GB/T 1040.2-2022 Plastics—Determination of tensile properties—Part 2:Test conditions for moulding and extrusion plastics GB/T 1040.3-2006 Plastics—Determination of tensile properties—Part 3:Test conditions for films and sheets GB/T 1040.4-2006 Plastics—Determination of tensile properties—Part 4:Test conditions for isotropic and orthotropic fibre-reinforced plastic composites GB/T 1040.5-2008 Plastics—Determination of tensile properties—Part 5:Test conditions for unidirectional fibre-reinforced plastic composites GB/T 1040.1-2025 Plastics—Determination of tensile properties—Part 1:General principles

Adopt standards

IEC 60544-2:1991

Related Standards

GB/T 5130-1997 Replaced

GB/T 5130-1997 Test methods for industrial rigid laminated sheets based on thermosetting resins for electrical purpose

Publish Date: 1997-06-03
MT 756-1997 Abolished

MT 756-1997 Test method of flame resistance property of polystyrene foam plastics for water trough for explosion suppression

Publish Date: 1997-12-30
GB/T 7113-2003 Replaced

GB/T 7113-2003 Flexible insulating sleeving—Definitions and general requirements

Publish Date: 2003-06-24
GB 12802.2-2004 Replaced

GB 12802.2-2004 Film for electrical insulation—Part 2:Polythylene terephthalate film used for eletrical insulation

Publish Date: 2004-02-04
GB/T 20875.1-2007 Active

GB/T 20875.1-2007 Method of test for the hydrolytic stability of electrical insulating materials—Part 1:Plastic films

Publish Date: 2007-01-23
GB/T 23641-2009 Replaced

GB/T 23641-2009 Fiber reinforced unsaturated polyester moulding—compounds(SMC and BMC)for electrical purposes

Publish Date: 2009-04-21
Contact Us