GB 6932-2001
Replaced
T/CECS 10363-2024
Active
Group standards
T/CECS 10363-2024 Flanges and flanged joints for thin-walled stainless steel pipe fittings
T/CECS 10363-2024 Flanges and flanged joints for thin-walled stainless steel pipe fittings
Price:
$ 43.00
Basic Information
Standard Code:
T/CECS 10363-2024
Standard Type:
Group standards
Standard Status:
Active
is_force_gb:
no
CCS Name:
Piping accessories
ICS Name:
The facilities in the building
Publish Date:
2024-02-22
Implement Date:
2024-07-01
Pages:
24 pages
Scope
This document specifies the classification, marking, type structure and dimensions, technical requirements, marking, packaging, transportation, and storage of flanges and flange joints used in thin-walled stainless steel pipe fittings (hereinafter referred to as "flanges" and "flange joints", respectively). It also describes the test methods and establishes inspection rules. This document is applicable to the design, manufacture, and acceptance of flanges and flange joints used in thin-walled stainless steel pipe fittings with a nominal size not exceeding DN300 and a nominal pressure of PN10, PN16, and PN25, which are used in industrial buildings and civil buildings for conveying domestic water, hot water, drinking water, air conditioning circulating water, compressed air, medical gases, and so on.
Development Information
Referenced Standards
GB/T 1804-2000 General tolerances for linear and angular dimensions without individual tolerance indications
GB/T 2828.1-2003 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection
GB/T 2828.1-2012 Sampling procedures for inspection by attributes—Part 1:Sampling schemes indexed by acceptance quality limit(AQL) for lot-by-lot inspection
GB/T 3098.1-2010 Mechanical properties of fasteners—Bolts,screws and studs
GB/T 3098.2-2015 Mechanical properties of fasteners—Nuts
GB/T 3098.6-2000 Mechanical properties of fasteners—Bolts, screws and studs made of stainless-steel
GB/T 3098.6-2014 Mechanical properties of fasteners—Stainless steel Bolts,screws and studs
GB/T 3098.6-2023 Mechanical properties of fasteners—Stainless steel bolts,screws and studs
GB/T 3098.15-2000 Mechanical properties of fasteners—Nuts made of stainless-steel
GB/T 3098.15-2014 Mechanical properties of fasteners—Stainless steel nuts
GB/T 3098.15-2023 Mechanical properties of fasteners—Stainless steel nuts
GB/T 4237-1992 Hot rolled stainless steel sheets and plates
GB/T 4237-2007 Hot rolled stainless steel plate, sheet and strip
GB/T 4237-2015 Hot rolled stainless steel plate,sheet and strip
GB/T 7306.1-2000 Pipe threads with 55 degree thread angle where pressure-tight joints are made on the threads—Part 1:Parallel internal and taper external threads
GB/T 9126.1-2023 Non-metallic flat gaskets for pipe flanges—Part 1:PN designated
GB/T 11170-1989 Method for photoelectric emission spectroscopic analysis of stainless steel
GB/T 11170-2008 Stainless steel—Determination of multi-element contents—Spark discharge atomic emission spectrometric method(Routine method)
GB/T 12716-2002 Pipe threads with the thread angle of 60 degrees where pressure-tight joints are made on the threads
GB/T 12716-2011 Pipe threads with the thread angle of 60 degrees where pressure-tight joints are made on threads
GB/T 19228.1-2011 Stainless steel press-fitting assemblies—Part 1:Press-fittings
CJ/T 152-2016 Light gauge stainless steel press-fittings and grooving fittings
NB/T 47010-2017 Stainless steel and heat-resistant steel forgings used in pressure equipment
NB/T 47010-2010 Stainless and heat-resisting steel forgings for pressure equipments
Related Standards
GB/T 19249-2003
Replaced
GB/T 19249-2003 Reverse osmosis water treatment equipment
GB/T 19913-2005
Replaced
GB/T 19913-2005 Cast iron heating radiator
CJ/T 245-2007
Abolished
CJ/T 245-2007 Syphonic roof outlet
CJ/T 133-2007
Replaced
CJ/T 133-2007 Integrated circuit card water meter
CJ/T 241-2007
Active